Teltonika TRB140 Digital & Analog I/O Module Digital & Analog I/O Modules (Digital & Analog, Input/Output, RJ-45, SSH, CLI, NAT, DDNS, OpenVPN, Green, 9-30V)

Product Information

Undertegnede TELTONIKA NETWORKS erklærer herved, at følgende udstyr TRB140 overholder de væsentlige krav og øvrige relevante krav i direktiv 2014/53/EU Network protocols TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SMTP, SSL v3, TLS, PPP, PPPoE, SSH, DHCP, SNMP, MQTT, Wake on LAN (WOL) This device is "half open-source". The operating system is based on OpenWRT, so you can gain access via SSH, but you won't be able to install a different OS. LTE performance Status LEDs 3 x connection type status LEDs, 5 x connection strength LEDs, 2 x LAN status LEDs, 1x Power LED

The Teltonika TRB140 Industrial LTE Cat 4 Gateway is equipped with a single Ethernet port, Digital Inputs/Outputs and a micro-USB port. The TRB140's compact design makes this Gateway perfect for an application where a sole gadget must be granted reliable Internet connectivity. TRB140 is engineered to be used in an Industrial application therefore it has a robust frame and a wide range of software features such as SMS control, Firewall, Open VPN, IPsec, RMS and FOTA support.This device meets the official requirements for exposure to radio waves. This device is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by authorized agencies. The device must be used with a minimum separation of 20 cm from a person’s body to ensure compliance with RF exposure guidelines. Failure to observe these instructions could result in your RF exposure exceeding the applicable limits. Hierbij verklaart TELTONIKA NETWORKS dat het toestel I TRB140 in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 2014/53/EU Ar šo TELTONIKA NETWORKS deklarē, ka TRB140 atbilst Direktīvas 2014/53/EU būtiskajām prasībām un citiem ar to saistītajiem noteikumiem Ensure that the voltage and the rated current of the power source match the device’s requirements. Do not connect the device to an inappropriate power source. Status Signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP Bytes sent/received, connected band, IMSI, ICCID.

The TRB140 is simpler and less expensive than 4G routers; consequently, it works well as part of a simple and inexpensive solution for getting reliable 4G connections to a network that otherwise wouldn’t have one. In conjunction with an external LTE antenna, for achieving a strong mobile signal, the TRB140 can be used as the WAN input for a cheap and cheerful Ethernet router such as the Tenda F300. In this scenario, the TRB would act as a basic 4G gateway while the Tenda F300 (or an equivalent device) acts as the network router. Käesolevaga kinnitab TELTONIKA NETWORKS seadme TRB140 vastavust direktiivi 2014/53/EU põhinõuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele sätetele Firewall: Pre-configured firewall rules can be enabled via the WebUI, unlimited firewall configuration via CLI; NAT; NAT-T Azure IoT Hub Can send device IP, Number of bytes send/received/ 3G connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, Sim State, PIN state, GSM signal, WCDMA RSCP WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server Cumulocity Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IPIPsec: IKEv1, IKEv2, supports up to 5 x VPN IPsec tunnels (instances), with 5 encryption methods (DES, 3DES, AES128, AES192, AES256) Attention: operation outside the permissible range can considerably shorten the service life of the device. The Teltonika TRB140 is less expensive than 4G routers as it does not perform any routing. Instead it is ideal as a simple solution to provide a 4G internet connection to a network that doesn’t have one. Alongside an external 4G LTE antenna the TRB140 can be used as a WAN for an ethernet router, which would do the routing. Mounting options: Bottom and sideways DIN rail, Flat surface and direct PCB on DIN-Rail mounting options External antennas used with TRB140 must be installed to provide a distance of at least 20 cm from any people and must not be co-located or operated in conjunction with any other antenna or transmitter.