Ubiquiti US-16-150W 150 W 16 Port UniFi PoE Switch

Product Information

It’s also worth pointing out that PoE devices don’t always consume their maximum rated power draw. The spec sheet will specify the maximum amount the device can use, but during normal operation they won’t use that much. For example, the U6-Pro requires 802.at PoE+ or 48V passive, and maxes out at 13W. During normal use it usually consumes around 5 to 7 watts of power. I have been working a lot with Unifi devices and sometimes you just got one of those devices that just won’t adopt. You may get an error that a firmware update is required or you can’t simply find the device in the controller. EdgeSwitches are more flexible and capable, and are a better fit for network operators, WISPs, managed service providers, and other more advanced networks. If you need features like link aggregation, TACACS+, RADIUS, 802.1X, MAC filtering, ACLs, or static routing, you’re better off with an EdgeSwitch than a UniFi switch. UniFi switches support many of these features, but are often less configurable, poorly documented, and less reliable.

If you keep having problems with the installation of the firmware you can also try to install it your self directly on the device. To do this we are going to access the device using SSH. I adopted it and upgraded the firmware. It took longer to unbox and mount it than it did to set it up.

A common complaint with the first generation models are their loud fans. It is possible to replace them with quieter Noctua fans, or you can throw it in a network closet and forget about it. If you just need basic L2 switching and PoE, the first generation models are still worth considering, especially if budget and availability are more important than future software support.

EdgeSwitches have an optional web interface overlay called UISP, which is similar to the UniFi controller. UISP is limited when it comes to EdgeSwitch configuration, and it doesn’t have every option that the device’s individual web GUI or CLI has. Think of UISP as an easy way to monitor all of your AirMAX, LTU and EdgeMAX devices, rather than a single interface for configuring everything like the UniFi controller. One limitation of the regular second generation switches is their limited PoE budget. PoE budget refers to the total amount of power available for all PoE devices. Since the non-pro 2nd generation models are fanless, they also have smaller power supplies, and a smaller PoE budget. Have lower fan noise — the non-pro models are fanless. The pros have fans, but are quieter than the 1st generation models. The Ubiquiti US-16-150W UniFi switch provides fiber connectivity options for easy expansion of your networks. Each Ubiquiti US-16-150W UniFi switch model includes two SFP ports for uplinks of up to 1 Gbps for network expansion and uplinks. UniFi Controller

I mounted it, plugged it in to power and the other switch I had. By the time I got upstairs, the controller already found the new switch. EdgeMAX products are managed with a per-device web interface, or via SSH. These web interfaces are not as polished or pretty as UniFi, but they expose more advanced features than UniFi does. EdgeSwitches also have the full EdgeOS CLI for configuration. If you’re familiar with JunOS or IOS, you’ll be able to figure out your way around. See Ubiquiti’s CLI Command Reference user guide for more details. A factory reset is useful for a creating fresh setup of a UniFi Console, or device that was already configured in a managed state. Restoring with the Reset Button Putting the L2/L3 differences aside, the 2nd generation pro models also have some other advantages over the non-pro UniFi switches. 2nd Gen Pro models add

EdgeSwitches are older, more traditional managed switches, with command line (CLI) and individual web interfaces for configuration. EdgeSwitches also have optional integration with the UISP software controller. The newer UISP-branded switches are tied closely to the UISP software, have no web interface, but still offer a CLI for manual configuration. I cover EdgeSwitch and UISP hardware briefly below, but I cover them in more detail in my UISP Switch review. The USW-EnterpriseXG-24 is a 2nd gen model, with twenty-four 1/2.5/5/10 Gbps RJ45 and two 25 Gbps SFP28 interfaces. No PoE. If you are planning on using PoE passthrough on switches like the USW-Flex, or access points like the In-Wall-HD, you should supply them with the higher-wattage PoE+ or PoE++. Devices with PoE passthrough will usually function when fed with standard 15W PoE, but will not reliably power downstream devices unless they receive their maximum rated power input. For example, the USW-Flex can provide 8W with PoE in, 20W with PoE+ in, and 46W with PoE++ in. Ubiquiti calls them “Gen2” but I am going to call them 2nd generation. Whatever you call them, Ubiquiti’s newer UniFi switches split things into a few tiers. There are models which replace the 1st generation switches, and the higher pro and enterprise tiers.Higher PoE budgets. The 2nd generation non-pro models are fanless and have very limited PoE budgets PoE+ devices like the U6-Pro will usually operate with 802.3af input, but they will be unreliable. It’s never a good idea to push past your budget, feed a PoE+ or PoE++ device with a lower tier of PoE, or supply the wrong voltage. Always follow the recommended input power, and never provide less the required power or a different voltage. The USW-Flex-XG is a 2nd gen model, with one 1 Gbps and four 1/2.5/5/10 Gbps RJ45 Ethernet ports. No PoE.