Yealink W60B DECT Base Station - Black

Product Information

Video tutorial explaining Auto Provisioning setup for Yealink Phone on PBXware 5. ¶ Requirements ¶ Identifying phone model The base station is what is provisioned by 3CX and registers via SIP to 3CX. The handset registers or pairs to the base station via DECT. Then you associate a handset with a line which is one of the SIP accounts provisioned on the base station: I had registered the MAC, IP, etc., all via the Cloud Voice cPanel, but it refused to work. I literally wasted days on this, and eventually gave up and called BT support. NB * the log file is not in the directorty above its in the /var/log/3cxsbc directory not /var/log. This step is not required for brand new out-of-the-box phones, however, if the phone has been already used then it is a must.

If there are multiple lines assigned to your handset as outgoing lines, press the Line soft key to select the desired line. If a line is not selected, the handset uses the default outgoing line to dial out.

Yealink W60P IP Dect Package (W56P + W60B)

Both BT Cloud Voice and BT Cloud Phone portals include facilities to add or delete new devices (licences) and no doubt there is an assumption someone is actively managing them. The issue may arise though on SME with a small number of lines, sending out preconfigured kit and people simply using the pre-setup or express setup. I think @cobaltit was correct in saying you are overthinking it and in your honest attempt to get it to work you appear to be introducing variables instead of eliminating them, so how about we start from scratch with a clean slate? The PIN is used to register handsets to the base station, and for the handset to access settings from the base station. When a Base and a handset are supplied together in a single box, then the handset should already be registered to the base station. You can use these steps to register additional handsets though: This chapter describes how to identify Yealink phone model, requirements that must be met and how to register the phone using manual configuration or auto provisioning.

I must say, not being able to access the cPanel is a bit annoying, as you lose access to certain features – i.e. directory, codec settings, etc. The phone will NOT register -> shown in the Account tab of the Phone's Yeaklink Web GUI. The Outbound Proxy server setting in the W60B firmware I can see is all set to the SBC's LAN IP and using port 5060, and its enabled. But still no dice.Note: You can ignore an incoming call by pressing the Silence soft key or reject an incoming call by pressing . Connect the ethernet cable between the Internet port on the phone and the network port on a router or switch to access LAN.

I think you are missing this step in the guide for actually putting the URL into the base station and you're going straight to the part about registering a handset to the base station: NOTE: Do not unplug or remove power to the phone while it is updating firmware and configurations. ¶ Registering phone I followed through the instructions above. The Base reset Ok, and once the base reset the handset automatically said de-register the handset? on the screen, so i pressed yes. The set of instructions thereafter to deregister the handset therefore could not be followed to de-register the handset as described as it had already de-registered itself and said so. It couldn't therefore do the handset reset. Using a regular ethernet cable, your phone can be powered from a Power over Ethernet (PoE) compliant router or switch.

Can you tell me if the ports in the PBX GCP Firewall all have to be open for remote handsets if the SBC is in the office? yes/no

The Yealink W60B/W70B is a DECT base station aimed at home as well as small and medium-sized businesses. Its main specifications are: So i used a logical workaround: I then managed to reset the handset in settings which failed before and then pressed the connect button on the base and managed re-register the handset from settings it then paired ok. Choose what server type you intend to use: HTTP, HTTPS and Trivial FTP. NOTE: Our recommendation is to use the HTTP. Based on wireless DECT standard to offer premium and stable HD audio quality for efficient and clear communication. Ok either your network is more complex then you describe, or you (and your head of IT) are really not understanding how 3CX is architected.. The standard for most firewalls is to deny all new inbound traffic, allow all outbound traffic, and to allow any inbound traffic in response to outbound traffic. Since all the phone and SBC traffic is outbound or inbound in response to outbound traffic you do NOT need any port forwarding, assuming your previous statements are correct. The SBC and the phone should be on the same LAN, thus the firewall should not be seeing any traffic between them, and thus no port forward. And the SBC has nothing listening on port 5001 since that is the web administration port for 3CX which is in GCP according to you. If you do not have a simple network then you need to describe or provide a network diagram. By simple I mean this:You then make sure you remove any port forwards from your office firewall that have anything to do with the SBC and the phones -> This is another variable eliminated Search for an entry by using the keypad to type letters, or press ▲ or ▼ to highlight the desired entry, and then press or to dial out using the default line. Now these are the errors (using Level = ERR) i can see in the log file,but I don't know what to do about them, perhaps you can help? (see attachment)