SONOFF Wi-Fi BasicR3 Switch Actuator

Product Information

Long press the button for 5 seconds to enter pairing mode, then press another 5 seconds to ender Compatible Pairing Mode (AP). The LED indicator should blink continuously.

September 25th, 2021, Update #1: Updated the curl commands to escape double quotation marks ( ") in the -d (HTTP POST data) argument. I also made other minor changes to improve command execution (e.g., setting up environmental variables for IP_SONOFF and IP_HOST), fix typos, and improve readability. The main voltage (AC) is separated from the circuit and in the narrower point it comes close to 2.4mm (reinforced with physical separation. Connectivity module Usable GPIO: - GPIO14 is broken out on the PCB adjacent to the GND pin. - GPIO13 - You must remove the bi-colour LED - GPIO04 - You must solder wire to pin on ESP chip Official Sources ~data1={“switches”:[{“switch”:”on”,”outlet”:0},{“switch”:”off”,”outlet”:1},{“switch”:”off”,”outlet”:2},{“switch”:”off”,”outlet”:3}],”sledOnline”:”on”} and once the webserver stops receiving GET requests, you know that it will then start flashing the firmware onto the device’s memory. The SONOFF devices [1] can work in either eWeLink mode or DIY Mode, In eWeLink mode, the device is connected with eWeLink cloud and controlled by eWeLink APP, while in DIY Mode, device publishes its capability service and is controlled by HTTP Post request. Sep/2021:12:51:30 -0300] "GET /tasmota-lite.bin?deviceid=10011b78f7&ts=5748438&sign=e177370169c2051e73f82c2cd3874da6d333e46ef597da91dc543cc573586b04 HTTP/1.1" 206 4399 "-" "itead-device" As with Sonoff Basic R3 board comes with GI-1A-5DH relay capable of 10A. This is exactly the same layout as well.

Get the info of “device ID”, “Service Type”, “device API interface version” and “device information” via parsing out the device DNS TXT Record. data1={“switch”:”on”,”startup”:”stay”,”pulse”:”on”,”pulseWidth”:2000,”rssi”:-67,”fwVersion”:”3.5.0”} The operation failed and the device does not exist. The device does not support the requested deviceid. Fortunately, there are alternatives that require flashing a different firmware onto Sonoff devices. The Tasmota firmware, for example, is a well-known alternative that provides easy integration with existing home-automation servers and let users control devices via multiple methods, such as webUI, HTTP requests, and MQTT, all of which can be accessed either locally or remotely or both. On top of that, it is free and open-source. Traditionally, flashing a Tasmota firmware onto a Sonoff device involves finding a serial connection, soldering a few cables/pins, and connecting the device to a serial-to-USB adapter. However, more often than not, this takes time, knowledge about electronics, and soldering very small components. I ended up flashing these Sonoffs with Tasmota using the excellent NODEMCU Firmware programmer http://www.nodemcu.com and or course, for putting in the initial WIFI configuration I use YAT – all on my Windows 10 PC.

Inching emulates a “long press of a push-button”. This will enable the relay for a short time then automatically turn the relay off. To use the setting you have to enable it and provide the pulse duration in ms (and increments of 500) in the range of 500 – 36 000 000. (0.5 sec – 10h). Submit the values to URL: http://192.168.1.12:8081/zeroconfig/pulse {"deviceid":"10008fxxx","data":{"pulse":"on","pulseWidth":2000}} The operation failed and the request parameters are invalid. For example, the device does not support setting specific device information. Take extra care when opening Sonoff R3. The button with the long actuator is prone to accidental damage. Sonoff R3 shell consists of 2elements – remove one by one to decrease the risk of breaking the button. To turn the Sonoff R3 on/off simply submit the correct value to the URL: http://192.168.1.12:8081/zeroconfig/switch {"deviceid":"10008xxxx",

Note: SONOFF BASICR2 does NOT have 433Mhz RF receiver module. If you want RF function, please buy SONOFF RFR2 . Documents If you are running firmware version 3.4 and below, you can use Sonoff DIY mode on R3 series devices equipped with a physical jumper, as of April 2020 firmware 3.5 version supports Sonoff DIY 2.0. Entering the Compatible Pairing Mode (AP) by long press the paring button for 5 seconds after power on User tips: If the device has been paired with eWeLink APP, reset the device is necessary by long press the pairing button for 5 seconds, then press another 5 seconds for entering Compatible Pairing Mode (AP)

MANUALS

The operation failed and the request body size is too large. The size of the new OTA firmware exceeds the firmware size limit allowed by the device. The connectivity module is identical with Sonoff Basic R3. It uses ESP8582 to communicate with the Internet and the same pins are exposed for you to use: Vcc, GND, TX, RX – These are the standard GPIO pins.