Plumb Pak K836-1 Standard Toilet Wax Gasket, for Use with 3 in Or 4 in Waste Lines

Product Information

Do you see the water at the bottom of the toilet bowl? It acts as a barrier for the sewer gases, and that is why you should always make sure the bowl has sufficient water. A small opening between the wax ring and the toilet is enough to let out a bad smell in your bathroom. As a starting point, put on your rubber gloves and get ready to begin. Firstly, you need to turn off the water valve and drain the toilet cistern. To do the latter, you’ll need to flush the toilet so that the cistern is empty. There might still be some water left in it, though, so remove the cistern lid and use sponges, cloths or towels to absorb the remaining moisture and water left in it. Once ready, you can proceed to the next step. Step 2. Disconnect the Water Supply Low Level Toilet Cistern - A traditional style cistern for traditional toilets; low level cisterns are fixed just above the pan and usually have a gap between them and the pan. Your toilet must be situated on a level surface to work correctly. If the surface slopes upwards or downwards, not only will your toilet not sit flush to the floor, it may not work properly. During the preparation, you must ensure that the surface is level before your plumber comes to fit it. Have you ever entered your bathroom only to be met by a horrific sewer odor? Apart from being water-tight, the wax ring should also create an airtight seal. If there is a small opening between the wax ring and the bottom of the toilet, sewer gases will leak from the drainpipe to the bathroom through that opening.

Before removing your old toilet, ensure that you have your new toilet ready to install right away. Toilet Installation Regulations Start off by removing the cistern lid, which should simply come off when lifted. It’s not usually attached to the cistern in any restrictive manner unless the toilet is fitted with a flush down button rather than a lever. From there, you need to use your screwdriver to unscrew the bolts at the base of the cistern. If you find that your flushing mechanism is faulty, replacing your flush button is a whole other topic to delve into. A: The components of the toilet, which are located within the cistern, will already be assembled and ready for use once your new toilet has been fitted. Q: How much does it cost to hire a professional to replace a toilet? A low-level toilet has a traditional look to it. This is where the cistern is fitted at a low level to the wall and is connected to the bowl via a pipe. These types of toilet look great in period homes. High-Level ToiletIf you plan on going to the tip to recycle or dispose of your loo then we always advise getting in touch with them first to make sure they will accept it; especially if you have to travel quite far. The mounting nuts on your toilet are the fixtures that hold the toilet to your floor in place. You will want to remove these, but if it’s problematic due to the nuts being rusty or old, as mentioned in the previous step, try to use a screwdriver or wrench to help you loosen and unscrew them. This may require some effort on your part as they may have been screwed on years ago and are, therefore, hard to lift out of place. Step 5. Cut Through the Caulk and Pull the Toilet Up

The problem with having stagnant water on your bathroom floor for too long is that it might cause it or the subfloor to start rotting, especially if it’s wooden. This can result in more expensive repairs. 2. Water leaking from the basement ceiling Some customers prefer to hide their cistern away, in so-called sealed cistern systems. The cistern itself can be mounted behind a wall, leaving only the pan exposed and accessible. Fitting a sealed cistern is more costly, with a suitable space created behind the cistern to house it. Installing a toilet requires very little tools and with modern pans you’ll find that it’s easier than ever. We have listed below the tools you will need to install a toilet, as well as some extras that may come in handy.

What’s involved with installing a new toilet?

Once you've done this, remove any leftover water in the bowl or cistern using an old sponge or rags. Step 4 High Level Toilet Cistern - Another traditionally styled cistern for a traditional toilet; high level cisterns are fixed high up on the wall above the pan and require a step or step ladder to gain access. These toilets are available in a range of modern and traditional designs, so you can easily find one that suits your bathroom's aesthetic. Corner Toilet It is recommended that you wear gloves when replacing your toilet to avoid getting any germs or bacteria on your hands. Materials to Replace a Toilet