STC-1000

Product Information

If measured temperature temperature set-point - temperature differential, the controller starts heating mode and heating indicator is on. Zahrnujeme zelený terminál, dvě svorky 1-2 jsou pro napájení AC 110 / 220V (230V), svorka 3-4 pro teplotní čidlo, svorky 5-6 pro topné relé 7-8 pro chladicí relé. The XH-W219 thermostat module with its STM8S µC and I/O (sensor input, keys, double display, relay) can be re-programmed for automation tasks, and it's easy to work with.

Arduino Nano wiring schematic Arduino Pro Mini + CP2102 (or CH340 or FT232 or any other similar USB to TTL serial adapter) Prevent a stalled fermentation: Too cold a wash can cause yeast inactivity, resulting in a stalled ferment. When the temperature of your wort drops below the ideal temperature, the controller increases the temperature, so it continues fermenting. High pressure cooling for water-based coolants or oil (pressures up to 150 bar / 2175 psi to get as close to the cutting zone as possible) Když připojím Termostat do sítě, tak mám na „vstupu 1“ napětí, signálka ukazuje „topení“, ale na vstupech 5 a 6 mi zkoušečka (jednoduchá tužková do zásuvky) neukáže žádné napětí, tj. nesvítí doutnavka.

The STC-1000 micro-thermostat from elitechu also has the same connection as its OEM version ,For this I just copy it here:

The material I use, Arduino pro mini, CP2102, 5 pin dupont cable and heat shrink tubing (optional). Jde mi voda z aku nádrže do radiatorů, ale chtel to nastavit tak, ze když voda z aku vychladne na 35stupnu zavře se ventil a zamezí průtoku z aku nádrže a sepne se el kotel a poběží stávající okruh topné sestavy mimo aku nadrz .. nevím kam přesně zapojit el systém zavíráni 3cv Elitech STC-1000 digital temperature controller thermostat is one of the most classic thermostats from the Elitech with automatic changeover between cooling and heating. It controls the temperature according to the temperature set value and the return difference. In the past, I made a review and manually for the generic OEM version of the STC-1000She had a good rating, and I have a good experience with her.The aim of the comparison between Elitech and the “Generic version” is to find out whether one is just a plain copy or Elitech has some added value.This firmware, in addition to act as a thermostat, has the possibility to update the setpoint (the desired temperature to keep) according to a schedule (a profile) once per hour. The main purpose of this firmware is control the temperature of fermenting beer. Micro temperature controller STC-1000is good stable choice .My experience is good with both versions from Elitech work in the hatchery3 thermostats, OEM version I sold about 18 pieces all run reliable. Elitech STC-1000 wirring and operation instruction manual: If measured temperature temperature set-point, the controller stops cooling and cooling indicator is off. F1: Nastavení cílovej teploty tlačítko pusch SET a zde vidět aktuálně nastavenou teplotu. Pokud ji chcete změnit, stiskněte znovu SET pomocí šipky nahoru nebo dolů (ať už chcete teplotu zvýšit nebo snížit). Pamatujte SET + šipku V popise je napísané, že termostat je veľmi presný a nastaviť sa dá po 0,1 stupňa. Mne po zapojení skáče hodnota nameranej teploty . Hodnota nepresnosti sa mení podľa toho , akú teplotu práve meria. Napríklad pri teplote 23 stupňov sa mení z 22,1 a skočí na 23, 0. Ale pri teplote 3,5 stupňa, skočí na 6 stupňov. To znamená že diferenciu 0,5 stupňa nastaviť je nereálne. Teplota nekolíše, ale skáče. Preto termostat stále cvaká, vypína a zapína.

If you are not able to solder, a temporary connection for programming can be made by simply pressing the pins of the pin header against the pads by hand. The board is coated, so you may need to clean the solder pads to make the connection. Nyní popíšu termostat a ovládání, pokusím se přesně popsat. Zařízení STC 1000 obsahuje pět hlavních komponent: Only when the sketch is uploaded correctly is it safe to make the connections to the STC-1000. Connect the STC-1000 It has functions of temperature measurement, temperature display, temperature control, temperature correction, sensor fault alarm, over-temperature range alarm, compressor protection delay. Elitech STC-1000Pro TH temperature controller thermostat with UK/EU/US version can be widely used in areas that need automatic temperature controls such as homebrew, pet breeding, seeding heat mat, aquarium, seafood machine, aquaculture, hatchery/incubator farming, greenhouse planting, brew, ferment, fridge, freezer, slow cooker, etc.The dimensions of the controller are 75mm (L) x 34mm (W) x 85mm (D) / 2.95 inches x 1.34 inches x 3.35 inches. Voltage

F2: Hysteresis od sleewe range :in manual called “Difference set value ” is gap when booth relay turn off…For example, if you set 1 degree Though the STC-10000 is the cheapest controller in the market, there are decent alternatives that won’t cost you an arm and a leg. Flip the pro mini upside down and the pins should line up (note: rx goes to tx and tx to rx, the others should match) It is recommended that you close the Arduino IDE once the sketch is uploaded and disconnect the programmer from the computer.An Arduino compatible development board (Arduino UNO or Nano or Arduino Pro Mini 5V 16Mhz) and the needed parts to connect it to a computer (USB cable or an USB/serial adapter for the Pro Mini) Sensors for bearing temperature, thermal spindle growth with compensation and in-process vibration monitoring