Lifetree Window Film Privacy: Privacy Film for Glass Windows Non-Adhesive No Glue Window Film Reeded Glass Decorative Patterned Static Cling Films for Home 44.5 * 200cm

Product Information

Thoroughly spray and soak the glass surface AND the static side of the film with the water mixture. Wetter is better! There is no such thing as too much water. The water will allow you to easily apply and reposition the film before you squeegee—and any excess water will evaporate after the film fully clings. Remove the protective liner to expose the adhesive layer. (It may help to place two pieces of masking tape either side and pull apart to separate) Give yourself enough space to work. You will need enough flat surface to lay out the film for measuring, cutting, marking and prep. Do not run a fan near the film or glass surface during installation. This can cause dust and debris to blow onto your film and become trapped. Steps Water bubbles are a factor in window filming that can not be avoided. Depending on the tools and pressure applied, you may remove up to 95% of the application fluid. The remaining 5% due to surface tension will form small bubbles and if left alone, will completely dry. This process normally takes no longer than 30 days but can take up to 60 days depending on the quality of installation. Using a pair of sharp scissors, cut the material roughly to size (We recommend 20mm extra on the Width and Height to allow the material to be cut to the shape of the glass) It is also advisable to make sure the Top of your film is straight and in line/square with any pattern.

With the exception of films specifically labeled and made for exterior application, always install film on the interior of a window. Film applied to the exterior will easily fail due to exposure to the elements. Warranty does not cover any damage to film during installation or any issues resulting from the improper installation of films.

We Supply and Fit Reeded Glass Film in the UK 

Wetting solution is the secret ingredient to a smooth, seamless installation. Make a solution by adding 8-10 drops of a mild, non-moisturizing dish detergent (Dawn or Joy; do not use hand soap) to a 32-oz. spray bottle filled with clean water (adjust ratio for smaller or larger bottles). More soap may be needed when applying film to acrylic surfaces. If you have hard water, consider using filtered or bottled water, to prevent mineral deposits under the film. Mix well. This designer-look is easier than ever to achieve at home, thanks to Purlfrost’s easy application. Once your made-to-measure reeded glass film arrives, spray the window and film with water and apply, making sure to smooth out any air bubbles and wrinkles – it’s as simple as that. The possibilities are endless; from internal and external windows to kitchen cabinets, shower screen through to a freestanding cupboard or even a glass coffee table. Starting from the Middle/Top, with your professional squeegee, push the water out towards the edges, and then down the middle with a liberal amount of force. This should create a T shape which creates a seal. (Note: If you encounter resistance between the film and squeegee, simply apply more of the application fluid.) Not sure whether this is the right film for your purpose? We offer free 10cm x 10cm samples. The pictures depicting the film are only for illustration purposes, so a sample is recommended to make an educated choice.

All films can be easily removed without any damage to the glass. Begin by peeling the film away from one corner of the glass and pulling down until the entire panel is removed. If any adhesive remains, it can be easily removed with window cleaner, soapy water or a single-edge razor blade. Before you do any actual cutting, you should consider where to place the seam on the window. You will usually have options when deciding: do you want it vertical or horizontal? Higher or lower? It may depend on the width of the roll you are working with, but generally you’ll want to place it where it is least noticeable. If you have tall windows, placing it at the top will make it harder to see. If it is darker at the bottom or people tend to look toward the top more often, then placing it at the bottom will be the best method. With the right preparation and installation, static cling Decorative Films are a fast and easy way to transform a room. But don’t skip steps or skimp on tools! For a beautiful and resilient end result, take your time, measure carefully, wet thoroughly and squeegee the entire surface. Before you get started…

We've added you to our mailing list!

Yes, most films can be installed on plexiglass, polycarbonate or acrylic surfaces. But unlike glass, some of these materials expand and contract with temperature changes and emit gas—which may cause air bubbles to form between the film and the surface. Use more soap in your wetting solution when installing on these surfaces. If you are applying a solar or safety film, apply as much pressure as possible to remove the water. You may need a specialist squeegee for this process. Thoroughly spray and soak the glass surface AND the adhesive side of the film with the water mixture. Wetter is better! There is no such thing as too much water. The water will allow you to easily apply and reposition the film before you squeegee—and any excess water will evaporate as the film fully adheres.